voiceover:the woodwhisperer is sponsored by powermatic, the gold standard since 1921 and by rockler woodworking and hardware, create with confidence. (lively music)
routers woodworking canada, the following video is part of the recent split-top roubo guild build. for more information about this project or to join the guild, goto woodwhispererguild.com.
marc:the power tool methodfor flattening a workbench is really pretty cool. it's a lot like a c&c machine. your router is going to go into a sled. that sled is going toride along two rails. these rails will be attachedto the outside of the bench. the idea is your bit isset at a fixed depth. anything that's higher than that depth gets chewed away by the router bit
and when it's all set and done you have a nice flat workbench. the reason why i like this so much is because this isn'tjust a single use jig, you can use this apparatus to flatten all kinds ofunwieldy large boards. if you have a real big slob that just is not going tofit through your plainer, you don't feel like taking the time
to try to flatten it by hand, you can use this systemto flatten it perfectly using the router. this is something you canjust kind of put the jig in the corner of the shopand there will be a time, i guarantee you where you're going towant to use this again. there's a few parts that we need to make but it's all made with cheap materials
and construction grade lumber. let's jump right into it. the router sled is going tobe comprised of three pieces, of three quarter inch plywood. you've got a base piece and then two fence pieces on either side. these fence pieces serve toguide the router back and forth but they also stiffen up this structure. without these, you're going to get a sag.
these prevent that from happening. the dimensions of thefences are four inches wide by 32 inches long. the 32 inches accounts for the fact that weneed to bring the router all the way out to the edge. if we terminate exactly at 24, we're never going to get there. we're going to have a partof the router unsupported.
we want to make sure weadd a few inches per side. i added four per side for a total of 32. now the base piece is abit of a different story. we're going to go to 32 inches. it should match the lengthof your fences pieces but the width is going to be variable. it's going to depend onthe width of your base. i really want the fences to sort of guide the base as it goes through.
what you need to do ismeasure the diameter. obviously this festal baseis kind of wacky looking. i just took this dimensionfrom the longest flat to the other end. if you have a circular base,it's a little bit easier and here's the formula. you take the width of the base and add an inch and a half and that accounts for your two fences.
the reason we add an inch and a half because i'm sure some of you are saying, "but marc plywood is not exactlythree quarters of an inch." that's actually going to work in our favor because these piecesare slightly undersized, that gives us just a littlebit of breathing room for that router. if it was perfectly tight, you would probably have trouble
sliding the router back and forth. that little bit was just basically about a 30 second of an inch under for each of these piecesis perfect for the router. take the width of yourbase, add an inch and a half and that should be thewidth of your base piece. before we attach ourfence pieces to our base, it's a good idea to removea channel of material for that router bit
because we're going to plunge down and move across the bench. it's a good idea if thatmaterial is already gone so we don't have to plowthrough it with the router bit. where this channel goesis really dependent on the shape of your base. you may notice thatmine is slightly offset. this is just a product ofthe way my base is shaped. the router bit just happensto land right there.
if you have a perfectly round base, you're going to bepretty much dead center. that's one thing that you need to know. the other thing is thewidth of this channel really just depends on thebit that you're going to use. if you decide to use something like our half inch router bit that we've been using in this project. all you really need is a channel
that's just a little bitwider than a half inch. now, you can use this but think about it. the size of this bench,it's going to take forever to go over this with a half inch bit. if you have the means, i do recommend going with something wider. this is a amana bit that's an inch and threequarters in diameter. this monster is going tochew away some material
pretty quickly and it's going to allow me to get through the entirebench in much less time. there's also a comparableone made by freud which you can check outthat's a little bit cheaper. i need to make sure that mybit is going to safely fit into this channel. my channel here is a littlebit wider than the bit itself. to cut this, i'm just goingto drill a couple of holes and use my jigsaw.
i'm just going to putone hole at each corner and before i go any further,i should mention that this line here stops aboutfour inches from the edge. i don't really need thisslot to be any wider than the work piece that thebit is going to have to cover. let me try and locate thisso i don't go over my lines but this does not haveto be absolutely perfect. using my jigsaw and avery fine tooth blade, i'm just going to dropthe blade into the whole
and essentially connect the dots and try to follow myline as best as i can. even using a really fine blade, you're still going to getsome tear out in plywood so just go ahead and sand that away. i've got my two fence pieces in place and i've got my base upside down and we could do the assembly this way. we can kind of just positioneverything where it needs to be
and then pre-drill and drive some screws into the fence material. what i want to do is makesure that i clamp these down because sometimes whenyou drive those screws, they have a tendency to push the material one way or the other. if there's a clamp there, it's going to be much less likely that that's going to happen.
we use a little bit of glue, i guess you don't really have to use glue but i kind of like to,just a nice thin bit. drop the base on top and all i really need to do is make sure that it's nice and flush on the ends and flush along the length. the other thing i want to point out is if your fence piecesare cut nice and straight,
those are what establishthe flatness of the base. if this had a big curve in it, the base would then conform to that. as long as you cut your pieces straight, you shouldn't have anyproblems with this base being nice and flat along its length. that feels pretty good. let me go ahead and add a clamp here. now i'm just going to pre-drilland counter sink for screws.
an inch and a quarterscrew should do the trick. now if i just flip the piece around, we can attach the otherfence in the same exact way. just like that, a router slide is born. probably not a bad idea tomake sure your router fits. here we go. this is exactly what we're looking for. as i mentioned before, the router sled is goingto ride on two rails
and those rails will beattached to the front and the back of the bench. those rails really can be madeout of just about anything that you can get a nice straight edge on. for me i don't really haveanything that's this long, a full eight feet longthat would work for this so i just went out and got a two by six, a construction grade two by six's. these are kiln dried,
i would recommend you gowith the kiln dried stock if you can get it because it would be morestable after you mill them. even with that, these tend to hold a lot more moisture than we're used to. when you mill them, do this process on the very same day. if you mill this ahead of time
and leave it for a coupleof days and come back, i guarantee you these edges will no longer be nice and straight. mine are freshly milled, ibasically just skip plain them. i had to make sure when i was at the store to get the straightest ones possible so that i could very easily skip plain and just put one jointed edge. you don't necessarily needthe other edge to be jointed
because we're onlyreferencing from one side. once you have them at this stage, the edge is nice and straight. we can attach them to thebench with a couple of clamps. if you got a helper, attaching this rails should be fairly easy. if you're by yourself,it's a lot more difficult. what i'm going to do is attach a couple of clamps to the bench.
one on each side and ikeep them fairly low, then i could bring my rail in like so. put it on top of that clamp and that should hold itin place temporarily. put one on the other side. with the two rails in position i could just take another clamp and clamp the rails to the bench, and one on this side too.
now we can remove thatfirst set of clamps, we don't need them anymore. they were just acting asanother set of hands basically. with the rails held in place we can now make some adjustments to get these rails in the right position. now, first of all they'rereally high right now. i want them down lowerbecause if you think about it, when the sled is moving back and forth,
we've got to plungethat bit down far enough to make contact with the bench. the higher these rails are, the further that bit has to travel. i'd rather not have to extend it too far. realistically, the rails don'tneed to be very much higher than the benchtop surface itself. i'm going to aim for i don'tknow, maybe a half inch, sounds good to me.
i'm going to take my dead blow. i'm going to start makingslight adjustments. if the rails are moving obviously you might want toloosen the clamp a little bit but not too much becauseyou don't want it to fall. i got my adjustablesquare, set to a half inch and i could just sight from the side here make little adjustmentsto try to get this rail just about a half inch above the bench.
do the same thing at this corner, and the same thing on the front left. i have a half inch on thisside, a half on this side and a half inch over there. that corner is the one that's unknown. really my goal at this pointis to get the two rails to be parallel with one another and i really rather not touch this one because it's even on thisside, even on this side
and i'm pretty confidentthat my front sled is fairly flat to begin with. i can clamp this front one in place and not really count on moving it at all. how do we make sure that that back rail is perfectly parallelwith this front rail? here's the old trick. basically you're going to take a string or some sort of a chord.
in this case i have someplastic coated metal wires. this is just sold bythe foot at home depot. it's got good visibility, it's thick, and it's going to help us seewhat we're trying to do here. i've already got one strungacross from corner to corner. let's install the second one from that corner to this corner. this is just temporary. i'm just going to use a screwwith a little washer here
and drive it into the rail. once i'm pretty close,i will take the string or your chord or whateveryou purchased for this. wrap it around the screw. it's a little hard to bend, and drill in. nice grip there. another screw at the diagonal corner and i could take my chord here
and wrap it around the screw. this one, you want to pull tight because you want this to bea fairly tight connection. i'm going to wrap it around, give it a good thug. tighten it up. let's take a look at wherethe two chords intersect and put your thinking cap on because sometimes this canbe a little bit confusing
to envision but essentially if our two rails are perfectly parallel with one another, these two strings wherethey meet in the middle will want to go right through each other. now of course they can't do that because they're made ofactual solid material. what we need to do is take this top string and we can take some cutoff material.
we need to raise this top chord, basically the thicknessof one piece of string. then when we come back and look here, when these two piecesjust kiss one another, when they first made contact we know that they're exactly parallel but it's only because weraised this top string by the thickness of one piece of chord. let's install those.
i'm going to slide it over here and put the other oneon the opposite corner. just a recap, the string that's on top now has a little cutoffunderneath it to raise it up on this corner and this corner. the other two are leftexactly as they were. now when these twostrings touch one another, we could be pretty sure that these rails are nice and parallel.
let's take a close look ofwhat we've got right now. we basically have a gapbetween the two strings here. it's about a quarter of an inch. the way we're going to resolve this is to tap one of the corners down until these two strings touch one another. before locking everything in, i want to go back and make sure that the three corners
that i had set at a halfinch are still there and it's a very good possibilitythat things have moved because we're hammeringon one of the rails. you just want to make sure that they're all on alignment, make any adjustments and keep going back and looking in the middle to make sure that those two strings arejust kissing one another. just as a bit of reality check,
i'm going to measure this by corner. this is the one that we know slopes up, we don't know how much it slopes up but i double checked and we're at a half inch everywhere else. if this slopes up and this rail is parallelto the rail in the front then we know that this distance should be less than a half inch.
in fact when i measure it, i've got about a quarterinch which tells me that this is a littlebit more of a slope up than i really thought it was if we have to remove a quarterinch extra material here. one more thing we cancheck in the dead center, i'll show you a neat little trick for making sure that those two chords really are just touching one another.
when you push down with justa little bit of pressure on the lower chord, you should not see thetop chord move at all. if it does move, it means that they're actually making a little bit too much contact. you would want to lift thetop chord up a little bit to remedy that. when i push down,
that top chord does not move at all but when i push down on the top chord, i can't even touch the top chord without the bottom chordmoving, do you see that? no movement at the top chord when i'm pushing down on the bottom an immediate movement wheni push down on the top. that tells me that these surfaces are just touching one another.
at this point i'm goingto tighten up my clamps and i'm even going to addanother one in the middle just for some extra support. of course we don't need the screws or the chords anymore. the goal now is to put oursled on top of the rails, drop a router in place and then we're just going to make one pass and move the router forward.
make another pass, movethe router forward. that's a lot of movementon this carriage here. it's probably a good ideato use a little bit of wax and that should makeit a little bit easier to slide this router back and forth. now your goal is to plunge the router down to what would essentiallybe the lowest spot of the workbench. i don't know absolutely for sure
but based on my measurements, my observations with the surface, i'm guessing that rightabout here at the end cap is going to be the lowest spot. now, it could very well beconsistent all the way across. we won't really know untilwe start cutting into it but this should be pretty close so that's where i'm going to start. i'm going to plunge this big old bit down
until it makes contact with the wood and then i'm going to tighten it up. i'm going to hold that settingfor the entire process. everything's in position. i'm just going to take my first pass and see how we do. after just a couple of passes, we could take a look at our progress. i did go back and i used the pencil
to mark up the surface and this gives us a goodvisual reference here and you could see the dividing line from where i've removematerial and where i haven't. this really is only abouta 30 second of an inch. that's not too bad especially for thisinitial flattening process. the other thing i want to note here is that we are cutting into our rails
and that's perfectly fine. these are sacrificial,they're meant to be cut into and you want to get the bit as close as you can to the edge. i'm not too worried about it if i've got a little bit ofmaterial to remove later, i could certainly do thatwith a scraper or a plane, that's not a problem at all. as you could see, with a bit like that,
at least you're pretty muchwith a nice smooth surface that really isn't going toneed a whole lot of work when it's all set and done. i'm just going to putthe router back in place and work my way across the bench. before i make my last pass, i just wanted to show youwhat we're dealing with here and that what we see actually confirms my suspicions early on
that my back slab hada bit of a twist in it. it's interesting because you think abouthow you get to this point and how something like this might happen and sometimes you can'teven really identify what you did wrong to cause this. the bottom line is withthe benchtop secured, we can now flatten this out,remove this extra stock, and be pretty confident that the benchtop
is going to be nice andstable, and stay flat. as you can see, i do have a substantial. i'm out of material that'sbeing removed at the back. at the front here, i'm still removing abouta 30 second of an inch, maybe a 16th of an inchat the most right here but it does get pretty deep in the back. this is one of those cases where i'm glad i did this with a router
because this would havebeen a heck of a lot of work to remove all thatstock with a hand plane. each method certainly has its merits but in some cases you mightfind the power tool method to be certainly less labor intensive. after a couple of minutes of vacuuming i can actually see thetop of my workbench again which is great. it turned out really nice.
of course the router bitleaves a little bit of a sort of scalloped pattern to the top. the truth is, you can keep that in there. you don't have to flatten that out because a lot of times your bench, if it has a little bit of texture to it, it's going to grip yourwork pieces better. i wouldn't necessarilyrecommend going at this with a smoothing plane justto make it glass smooth
because the more slipperyyour workbench top is, the harder it's going to be to work on. i'm probably just goingto hit this with a sander or maybe a cabinet scraper just to do some further smoothing. i should also point out thati have little triangles here that were left becausei'm using a circular bit. it only goes so far, and it winds up just leavingthis little triangle,
very easy to get rid ofthat with a block plane. now even though the rails for this flatteningprocess were sacrificial, the sled is not. this is something that you can hang on to and reuse again in the future. in fact, in the future it'sprobably going to be even easier because if you have a slab of material you could just lay thatdown on the workbench,
take some shims, makesure it's nice and stable and sitting flat. then all you need to do isgrab two new rail pieces and rest them on the bench as long as the bothsides of that rail piece are parallel with one another. basically you joint one edge and then rip the other at the table saw. place those down, clampthem to the workbench.
you now have a perfect reference surface because the bench is flat. the reason we had to dothe string thing before is because we really didn'thave a perfectly flat reference. we just clamped to the outside and needed to make surethat those two rails were in the same plane. in the future, it's much easier and if you have the ability to get a hold
of some sort of metal rails or something, you might even want tocheck out metal studs and see if those are nice and true you can have a permanent solution for flattening large projects. think about an end grain cutting board, there's something a lot of people have trouble flattening. wouldn't it be great to just slap it down
and within a couple ofminutes with the router, you have a nice flat board to work with. that's something you can do if you've got this carriage setup. now here's the thing, this is very basic. this is as bare bones of a setup as you could possibly get but you could get prettyelaborate with it. in fact fine woodworking,a couple of issues ago.
in fact it's december 2011, had a great article withthe dude from community apparently does a lot oflarge natural edge slab tables and things like that. he has got a very elaborate setup and his sled is much moresophisticated than ours but it's a really nice shop made solution for flattening large surfaces. if you want to reallyspice it up a little bit,
check out that article and e-mail me with your ideas because i'd love to see them. (mellow music)
